Home > Products > LED SMD > Chip LED > TO-1010BC-MRPBDED-5

[SMD Led Chip] TO-1010BC-MRPBDED-5

Surface Mount Device LED

Part Number Chip Lens Color
Material Source Color
TO-1010BC-MRPBDFD-5 AlGaInP Ulira Bright Red Water Clear
InGaN Pure Green
InGaN Blue

LED SMD TYPE:Single Chip

Type Dimension (mm) Chip Surface size λd (nm) Iv(mcd) at If=20mA Viewing Angle Document
L W H Min. Max.
Single Chip 0 0 0 mm2 - - - - Download PDF

Features

  • IC compatible. Top view type. RoHS compliant.
  • Compatible with automatic placement equipment.
  • Compatible with infrared and vapor phase reflow soldering process
  • Package in 8 mm tape on 7” diameter reel.
  • Moisture sensitivity Level: level3

Dimensions

Notes:

  1. All dimensions are in millimeter.
  2. Tolerance is ±0.1mm unless individual mark noted.

Absolute Maximum Rating @ Ta=25°C

Parameter Maximum Rating Unit
MR P B
Peak Forward Current(1/10 Duty Cycle, 0.1ms Pulse Width) 80 135 135 mA
Power Dissipation 26 32 30 mW
Continuous Forward Current 30 30 30 mA
Reverse Voltage 5 5 5 V
Operating Temperature Range -40°C to +80°C
Storage Temperature Range -40°C to +85°C
IR Reflow Soldering Profile For Lead Free Soldering 260°C for 10 sec

Electrical / Optical Characteristic @ Ta=25°C

Parameter

Symbol

MR

P

B

Unit

Test Condition

Min.

Typ.

Max.

Min.

Typ.

Max.

Min.

Typ.

Max.

Luminous Intensity

Iv

14

-

51

39

-

146

14

-

51

mcd

IF=5mA

Viewing Angle

2θ1/2

-

120

-

-

120

-

-

120

-

deg

IF=5mA

Forward Voltage

VF

1.8

-

2.4

2.8

-

3.4

2.8

-

3.4

V

IF=5mA

Dominant Wavelength

λd

620

-

635

520

-

535

460

-

475

nm

IF=5mA

Spectral Line Half-Width

λ

 

22

-

-

30

-

-

30

-

nm

IF=5mA

Reverse Current

IR

-

-

10

-

-

10

-

-

10

µA

VR=5V

Bin Code List for Reference

MR:

Luminous Intensity                                                                               Unit:mcd@5mA
Bin Code Min Max
C4 14 18
D1 18 23
D2 23 30
D3 30 39
D4 39 51

P:

Luminous Intensity                                                                               Unit:mcd@5mA
Bin Code Min Max
D4 39 51
E1 51 66
E2 66 86
E3 86 112
E4 112 146

B:

Luminous Intensity                                                                               Unit:mcd@5mA
Bin Code Min Max
C4 14 18
D1 18 23
D2 23 30
D3 30 39
D4 39 51

Tolerance of Luminous Intensity on each bin is ±15%

Optical Characteristic Curves

Reliability Tests

Test Item Test Condition Test Time
Thermal Shock -40°C * 10mins ~80°C * 10mins 300 cycles
Temperature Humidity Storage Ta= 65°C, RH= 90% 500hours
High Temperature Storage Ta= 100°C 500hours
Low Temperature Storage Ta= -40°C 500hours
DC Operating Life Ta= 25°C, 20mA 1000hours
Resistance to Soldering Heat IR-Reflow Normal Process Refer to recommended profile 1 time
Resistance to Soldering Heat IR-Reflow Pb Free Process Refer to recommended profile 1 time

1010 SMD Chip LED Lamps Packaging Specifications

Note:4,000pcs/Reel.

Soldering Profile

Reflow Soldering

Hand

Soldering

 

Lead Solder

Lead-free Solder

 

 

Pre-heat

120~150°C

180~200°C

Temperature

350°C Max

Per-heat time

120 sec Max

120 sec Max

Soldering time

3 sec Max

Peak Temperature

240°C Max

260°C Max

 

(one time only)

Soldering time

10 sec Max

10 sec Max

 

 

Condition

 

 

 

 

  • Rework

  1. Customer must finish rework within 5 sec under 260℃.
  2. The head of iron can not touch copper foil
  3. Twin-head type is preferred.

Cautions

The LED’s are devices which are materialized by combining blue LED’s and special phosphors. Consequently the color of the LED’s is changed a little by an operating current. Care should be taken after due consideration when using LED’s.

(1) Moisture Proof Package:

When moisture is absorbed into the SMT package it may vaporize and expand during soldering. There is a possibility that this can cause exfoliation of the contacts and damage to the optical characteristics of the LED’s. For this reason, the moisture proof package is used to keep moisture to a minimum in the package.

(2) Storage Conditions

Before opening the package:

The LED’s should be kept at 30°C or less and 60%RH or less. The LED’s should be used with in a year. When storing the LED’s. Moisture proof packaging with absorbent material (silica gel) is recommended.

After opening the package:

The LED’s should be kept at 30°C or less and 50%RH or less. The LED’s should be soldered within 168 hours (7days) after opening the package. If unused LED’s remain, they should be stored in moisture proof packages, such as sealed containers with packages of moisture absorbent material (silica gel). It is also recommended to return the LED’s to the original moisture proof bag and to reseal the moisture proof bag again. If the moisture absorbent material (silica gel) has faded away or the LED’s have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment: more than 48 hours at 65±5°C Oasistek LED electrode and lead free are comprised of a silver plated copper alloy .The silver surface may be affected by environments which contain corrosive gases and so on. Please avoid conditions which may cause the LED to corrode, tarnish or discolor.

This corrosion or discoloration might lower solderability or might affect on optical characteristics. Please avoid rapid transitions in ambient temperature, especially in high humidity environments where condensation can occur.

(3) Heat Generation

Thermal design of the end product is of paramount importance. Please consider the heat generation of the LED when making the system design. The coefficient of temperature increase per input electric power is affected by the thermal resistance of the circuit board and density of LED placement on the board, as well as other components. It is necessary to avoid intense heat generation and operate within the maximum ratings given in this specification. The operating current should be decided after considering the ambient maximum temperature of LED’s.

(4) Cleaning

It is recommended that isopropyl alcohol be used as a solvent for cleaning the LED ’s. when using other solvents, it should be confirmed beforehand whether the solvents will dissolve the package and the resin or not. Freon solvents should not be used to clean the LED’s because of worldwide regulations. Do not clean the LED’s by the ultrasonic. When it is absolutely necessary, the influence of ultrasonic cleaning on the LED’s depends on factors such as ultrasonic power and the assembled condition. Before cleaning, a pre-test should be done to confirm whether any damage to the LED’s will occur °C

(5) Static Electricity

Static electricity or surge voltage damages the LED’s. It is recommended that a wrist band or an

anti-electrostatic glove be used when handling the LED’s. All devices, equipment and machinery must be properly grounded. It is recommended that measures be taken against surge voltage to the equipment that mounts the LED’s. When inspecting the final products in which LED’s were assembled, it is recommended to

check. Whether the assembled LED’s are damaged by static electricity or not, it is easy to find static-damaged LED’s by a light –on test or a VF test at a lower current (below 1mA is recommended). Damaged LED’s will show some unusual characteristics such as the leak current remarkably increases, the forward voltage becomes lower, or the LED’s do not light at the low current. Criteria (Vf>2.0V at If=0.5mA)

(6) Others

Care must be taken to ensure that the reverse voltage will not exceed the absolute maximum rating when using the LED’s with matrix drive. The LED light output is strong enough to injure human eyes. Precautions must be taken to prevent looking directly at the LED’s with unaided eyes for more than a few seconds. Flashing lights have been known to cause discomfort in people, you can prevent this by taking precautions during use. Also, people should be cautions when using equipment that has had LED’s incorporated into it. The LED’s described in this brochure are in tended to be used for ordinary electronic equipment (such as office equipment , communications equipment, measurement instruments and household appliances) Consult Oasistek’s sales staff in advance for information on the applications in which exceptional quality and reliability are required, particularly when the failure or malfunction of the LED’s may directly jeopardize life or health (such as for airplanes, aerospace, submersible repeaters, nuclear reactor control systems, automobile, traffic control equipment, life support systems and safety devices). User shall not reverse engineer by disassembling or analysis of the LED’s without having prior written consent from Oasistek when defective LED’s are found, the User shall inform Oasistek directly before disassembling or analysis. The formal specifications must be exchanged and signed by both parties before large volume purchase begins. The appearance and specifications of the product may be modified for improvement without notice